In development · Essential tremor

TremET Band

Working toward objective tremor measurement between appointments.

TremET is an investigational device. It is not FDA cleared and is not available for sale.

Concept rendering of a slim navy wristband standing on a dark surface, with a small amber indicator light.
Design concept rendering. The band has not been built, and its form and finish are not final.

Essential tremor is assessed in clinic, a few minutes at a time, on a scale read by eye. TremET Band is a slim, screenless wristband being developed to measure hand tremor through the day and to log each medication dose with a single press, so the picture between visits could be measured rather than recalled.

The problem

What happens between visits is largely unmeasured

01

Assessment is episodic

Tremor is rated during a visit that may last minutes, then not observed again for months. Day-to-day variability, medication response and fatigue effects fall outside the window.

02

Rating scales are observer-read

Clinical scales such as TETRAS depend on trained visual assessment. They are the accepted standard, and they carry inter-rater variability that instrumented measurement is intended to reduce.

03

Instrumented options are not routine

Quantitative tremor measurement exists, but most systems are specialised equipment that is not part of routine practice, so measurement between visits remains rare.

Approach

What TremET is being built to do

The system is in active development. The description below is of intended function. Performance has not been established, and no clinical performance claim is made or implied.

Wear

Worn, not operated

A screenless band with a six-axis motion sensor and an optical heart-rate sensor is designed to record hand and wrist motion passively through the day. There is nothing to hold and no task to perform.

Design concept animation.

Log

One press per dose

The wearer presses the face of the band once after taking a tremor medication, so each dose is time-stamped against the motion recorded around it.

Concept rendering of a person pressing the face of a navy wristband at a kitchen table.
Design concept: logging a dose with a single press. Illustrative scene.

Summarise

A daily summary and a between-visit report

A companion app is being developed to show the wearer a simple daily summary, and to give the clinician a report of how tremor changed across days and doses, for review at their discretion.

The band

What the band is designed to include

The sensing, radio, battery and feedback components sit in a single enclosed pod on a soft fabric strap, with no screen and nothing for the wearer to assemble. Component selection is still in progress. The specification below is a design target, not a production configuration.

Sensing
Six-axis inertial measurement unit (accelerometer and gyroscope); optical heart-rate sensor
Input
Press face on top of the pod, used to log a dose
Feedback
Indicator light and gentle vibration
Link
Bluetooth Low Energy to a companion app (iPhone; Android planned)
Set-up
Tap-to-pair with a phone over NFC (planned)
Power
Rechargeable cell; magnetic charger that clips to the side of the pod
Form
Screenless pod on a fabric strap. Design target 37 × 20 × 9.5 mm
Concept rendering of the band pod in side profile on a dark surface.
Side profile of the pod. Design concept.
Close-up concept rendering of the band's recessed press face and amber indicator light.
The press face and indicator light, close up. Design concept.
Concept rendering of the top of the band, with a recessed press face and a small indicator light.
Top face and indicator light. Design concept.
Concept rendering of the underside of the band, showing an optical sensor window.
Underside, with the optical heart-rate window. Design concept.
Concept rendering of the band next to a small magnetic charger.
Magnetic two-pin charger. Design concept.
Concept rendering of the band in navy, black and light grey.
Colour exploration. Finishes are under consideration, and none has been selected.
Concept rendering of an older adult holding a mug, wearing the band.
Designed to be worn through the day. Design concept; illustrative scene.

Electronics

Electronics sized for the wrist

TremET's first instrument was a sensor pen. Every off-the-shelf development board was wider than the pen, so we laid out a custom circuit board to fit inside it. The band follows the same approach: the circuitry is being laid out for the wrist pod, rather than adapting a generic board, with a contract engineering partner.

Sensing
Inertial measurement unit; optical heart-rate sensor
Radio
Bluetooth Low Energy, antenna integrated
Charging
Magnetic contacts, on-board charge management
Feedback
Indicator light and vibration motor

The band electronics are in design. No band unit has been built.

How we built the pen's circuit board →
Exploded concept rendering of the band's pod, showing shell, circuit board, battery and housing.
Exploded design study of the pod. The component layout is illustrative and is not a production configuration. Design concept.

Regulatory

Pursuing FDA 510(k) clearance

TremET is being developed toward a premarket notification under product code GYD. TremET has not been cleared by the FDA, and it may not be sold or promoted as safe or effective unless it is cleared.

We are not currently running a clinical investigation. No study is enrolling and no investigational results are available.

Device class
Class II
Product code
GYD
Regulation
21 CFR 882.1950
Pathway
Premarket notification — 510(k)
Current status
In development — not cleared

TremET is an investigational device. It is not FDA cleared and is not available for sale.

Front and side elevations of the TremET Band pod, design targetFront view: a pod 37 mm long and 20 mm wide with rounded ends, a recessed oval press face 31 by 14 mm, and a small indicator light near one end. Side view: the pod is 9.5 mm thick overall, including a 0.7 mm raised sensor window centred on the underside. The strap is not drawn.FRONT20 mm37 mmSIDE9.5 mm (incl. 0.7 mm sensor window)
Front and side elevations of the pod. Design target; dimensions and enclosure are not final. Strap attachments add length on the wrist.

Progress

Where development stands

TremET is in active development. The steps below describe the current stage of work. No clinical study is underway.

  1. Done: Pen prototype and custom circuit board

    Our first instrument, a sensor pen, with a custom circuit board designed to fit inside it. The first assembled boards have been received. It shaped what the band needed to do.

  2. Done: Band industrial design concept

    External form, materials and controls for a slim, screenless wristband.

  3. Active: Band prototype engineering

    Electronics and enclosure for the first wearable prototypes, with a contract engineering partner.

  4. Active: Bench testing

    Verification of the assembled hardware and firmware on the bench.

  5. Upcoming: Fit and sizing studies

    Printed models worn on the wrist to settle size, strap and the position of the press face.

  6. Upcoming: Planned pilot study

    A study, subject to ethics review, to compare the band's measurements with clinician rating scales.

  7. Upcoming: FDA Pre-Submission

    Early feedback from FDA on the regulatory pathway.

TremET is an investigational device. It is not FDA cleared and is not available for sale.

How we got here

From a pen to a band

TremET began as a sensor pen, an instrument a patient would hold for a few minutes of guided writing tasks. Building it taught us how to fit sensing electronics into a very small enclosure, and it is where our patent filings began. In October 2026 we moved to a wristband, after feedback from investors favoured passive, all-day measurement over short tasks a patient has to remember to do. Work on the pen is paused.

Design concept render showing the full length of the TremET pen at a three-quarter angle: a tapered white body with an orange grip sleeve over the front section, and the orange control module and status light near the midpoint.
Earlier pen prototype concept. Development is paused.

Team

Who is building this

TremET is a two-founder company based in New York. The device concept is patent pending.

Tarush Oberoi

Co-founder & CEO

Farmingdale, New York

Co-inventor. Leads hardware, firmware, the companion app, regulatory and clinical planning, and the design-control documentation.

Eden Lau

Co-founder

Dix Hills, New York

Co-inventor. Co-leads outreach, partnerships and clinic engagement, and works with the company's legal counsel.

Clinical and research enquiries

We are interested in speaking with movement-disorder clinicians and practice managers about measurement needs between appointments. This is a conversation about unmet need and study design — not a sales process, and not a solicitation of orders.

tremet.contact@gmail.com